Warning! To avoid personal injury or even death, always disconnect your appliance from its power source–that is, unplug it or break the connection at the circuit breaker or fuse box–before you do any troubleshooting or repair work on your appliance. Also, because some components may have sharp edges, use caution while working on your appliance.
If you still can’t find anything to help, give us a call at (562) 239-3760, we’ll be right out!
Refrigerator repairs might include dealing with Freon and sealed system. It is strongly recommended that you seek the assistance of a qualified appliance technician.
If your refrigerator is not running or is not cold enough.
1. Turn the thermostat up to the next highest setting. If it comes on, let it run for 24 hours and check temperature to confirm it is working properly.
2. Clear/remove anything blocking the air flow around the outside of the refrigerator (on top, underneath, behind, beside, in front of, etc.). Allow 3″ of clearance all the way around.
3. If there are condenser coils on the rear of the box, make sure the box is several inches from the wall and that nothing is on top at the rear, blocking the heat from coming off the coils.
4. If the condenser coils are underneath the refrigerator, clean the coils with a vacuum cleaner thoroughly at least twice a year.
5. Refrigerator coils located underneath the refrigerator should be cleaned annually.
6. Refrigerators that constantly run can indicate improper functioning due to low refrigerant level, a dirty condenser coil, a malfunctioning seal, or improper air flow.
Ice or water dispensing problems.
1. If the ice or water isn’t dispensing check for a leaky water tube or jammed ice chute.
2. If ice maker is producing ice poorly check for clogged water line or defective water inlet valve.
3. Ice maker has stopped producing ice. Check to see if the ice maker has been turned off
If the door is sticking or not closing properly.
1. Wipe off the face of the gasket with a wet rag and make sure the interior shelves, drawers and food are not preventing the door from closing from the inside.
If it’s not working.
1. Check to see if power is getting to the range/oven. Does anything turn on, even a light? Check for blown fuse or tripped circuit breaker.
2. Is the power cord burned through; often it gets burned and breaks the connection.
Electric – If your burners are not heating.
1. Make sure they are sitting straight in their proper positions.
Electric – If your oven is not heating or not heating correctly.
1. Make sure the clock is set on manual cycle and not the automatic time bake cycle.
2. Is the bake element is burned out.
3. Check the heating thermostat bulb is dislodged from its holder. It could also be mis-calibrated.
Gas – If the top burners are not lighting.
1. Wipe off the burner with a hot, damp rag and then dry completely.
2. If top burner doesn’t work check for a dirty or clogged burner. Make sure burner is clean.
Gas – If your oven is not heating.
1. Make sure the clock is set on the manual and not the automatic cycle.
2. Raise up the top and keep the area clean and free of grease build-up.
No Power to dishwasher.
1. Check for tripped circuit breaker or blown fuse
2. Check wall socket for power
If the dishes are not getting clean.
1. Make sure the water is hot enough. It should be at least 140 degrees, which is hot enough to burn you – VERY HOT! If it is not hot enough, turn the hot water heater thermostat up to a higher setting.
2. Make sure the lower spray arm is unobstructed and turning freely.
3. Make sure the bottom inside the dishwasher is clean and free of debris.
4. Make sure you are following the proper loading procedures. Use the proper amount of detergent and make sure the detergent is fresh (check expiration or “best if used by” date).
5. Mold may grow in your dishwasher if you use it infrequently. The mold can be removed by using the normal dishwasher detergent and running the dishwasher, preferably without any dishes.
If the door isn’t closing.
1. Make sure the latch assembly is unrestricted and latching properly. Make sure nothing is blocking the door from opening and closing properly.
It isn’t draining.
1. Air Gap is clogged. Unscrew top cap and see if there is anything blocking it.
2. Drain hose is clogged Remove and clean the hose.
If the unit is leaking.
1. Make sure you are following the proper loading procedures, including proper type and amounts of detergents. Run the unit through cycle while empty – if it doesn’t leak, it’s probably a loading problem.
2. Make sure the racks are positioned properly.
3. Make sure the door is unrestricted around the opening.
If machine doesn’t work at all.
1. Make sure power is getting to washer. Check for tripped circuit breaker or a blown fuse.
2. Check wall socket for power. Sometimes the power cord disconnects at the washer.
3. Make sure the lid is closed properly.
4. Make sure the timer and all of the controls are set properly.
5. Make sure both water faucets are turned on.
• Important Tip – Follow the proper loading procedure and machine operation.
• Important Tip – Never overload the machine.
No power to the dryer.
1. Check for a tripped circuit breaker or blown fuse. Check wall socket for power with voltmeter.
2. Check for broken door switch.
If the clothes are not getting dry.
1. Make sure the dryer is not pushed back against the rear exhaust duct causing an air flow restriction.
2. Make sure the clothes are coming out of the washer spun damp dry. If the washer is not spinning the clothes damp dry, the dryer will not dry the clothes in a normal amount of time.
3. Turning your clothes inside out and using the delicate cycle can reduce the pilling effect on certain fabrics.
4. Cleaning the dryer filter before each load increases the efficiency of the machine and decreases the chance of fire.
5. Clean out the dryer vent hose, as well as the rest of the vent duct.
• Important Tip – Follow the proper loading procedure and machine operation.
• Important Tip – Never overload the dryer.
If the unit is not self-defrosting and the temperatures begin to rise.
1. Check the frost buildup on the inside of the freezer. If it is heavily frosted, manually defrost the freezer by turning it off at the thermostat. Unplug from the wall and allow 12 hours for the unit to defrost, with both doors open.
If the unit is not an automatic self-defrosting model.
1. Defrost the unit once a year or as often as needed. Follow the proper defrosting methods. DO NOT USE a knife, pick, hammer, chisel, screwdriver, etc. or any sharp object.
• Important Tip – Follow all procedures outlined under the refrigerator heading.
• Important Tip – Do not pack the freezer.
One important maintenance tip for refrigerators is to ensure proper air flow around the outside of the appliance. This includes clearing or removing anything that may be blocking the air flow, such as items on top, underneath, behind, beside, or in front of the refrigerator. It is also crucial to clean the condenser coils on a regular basis, especially if they are located at the rear or underneath the refrigerator.
Another key tip for refrigerator maintenance is to check for any signs of improper functioning, such as constant running. This could indicate issues like a low refrigerant level, dirty condenser coils, malfunctioning seals, or improper air flow. By following these maintenance tips, you can help ensure that your refrigerator operates efficiently and effectively.
To keep your dishwasher in optimal condition, it is important to regularly clean and maintain it. Start by checking the detergent you are using and making sure it is fresh and the proper amount is being used. Additionally, if you notice mold buildup in your dishwasher, run a cycle with normal dishwasher detergent and no dishes to remove it.
Proper loading procedures are also crucial for dishwasher maintenance. Make sure you are loading dishes correctly and using the right type and amount of detergent. If you experience leaks, it may be due to overloading, so be mindful of the dishwasher's loading capacity. By following these tips, you can keep your dishwasher in good working condition.
For washing machines, it is important to avoid overloading the machine to ensure proper spinning of clothes. If clothes are not spinning damp dry, it can affect the drying time in the dryer. Similarly, for dryers, always clean out the vent hose and duct to prevent lint buildup, which can lead to inefficient drying.
If your freezer is heavily frosted, it is recommended to manually defrost it by turning off the thermostat and allowing it to defrost with both doors open. Never use sharp objects to remove frost as it can damage the appliance. By following these care tips for washers, dryers, and freezers, you can prolong the life of your appliances and prevent issues down the line.